1. <table id="s6qli"></table>

        <td id="s6qli"></td>

        全國服務熱線:

        15853163650
        您當前的位置:首頁 > 新聞動態 > 行業新聞
          聯系我們

          CONTACTS US

          濟南皓暉建材有限公司,總部位于中國泉城——山東濟南,是一家專業生產銷售石塑電梯門套,仿大理石電梯門套的專業廠家。皓暉建材在電梯門套生產行業很多年,憑著優質的產品質量和完善的售后服務,在全國各地都有我們的工程案例。

          我們本著“以質量求生存 ,靠管理出效益,憑信譽贏口碑,以實干筑輝煌”的經營理念,公司將立足于當代建材現代化發展前沿,依靠科技、勇于探索,以優質產品優良服務、信譽與廣大用戶攜手共創輝煌。

          聯系電話: 15853163650

          工廠地址:山東濟南章丘區(歡迎廣大客戶來廠勘察)

        行業新聞

        COMPANY NEWS

        石塑電梯門套的安裝方法

        2018-05-07 15:58:47 文章來源:www.annexegallery.com

        石塑電梯門套裝置 :假如是傳統方式——現場制造的門套,是由現場裝飾工人間接用釘子固定于門洞墻 門套體;而假如是成套門商品的門套裝置(如今越來越多的用戶均采用成套門商品),則要思索兩個成績:

        Stone plastic elevator door sleeve device: if it is the traditional way - the field - made doorcase is fixed by the field decoration workers indirectly by the nail on the doorway body; and if the door set of the complete door commodity (now more and more users are using a complete door commodity), we should think about two achievements:

        一石塑電梯門套是相應的成套門商品,其門套的技術構造能否契合作爲成套門商品所須具有的結實性、精準性以及波動性這三大技術特征;

        The one stone plastic elevator door is the corresponding complete door commodity, and the technical structure of its door sleeve can fit the three technical features of the set door commodity, which must have the firmness, the precision and the volatility.

        二裝置者關于裝置現場的事前勘測與裝置時的工藝流程的標準性(如采用發泡劑等方式關于電梯門套結實性、精準性和日后運用的波動性一切能夠發生的影響)。

        Two the standardization of the process flow during the site survey and installation of the device (such as the effects of blowing agent on the sturdy, precision, and the volatility of the post - day application).

        1、依據設計圖紙反省門的規格、開啟方向、相關配件等。

        1、 according to the design drawings, reflect the door specifications, opening direction, related accessories and so on.

        2、用卷尺量門洞的高與寬。門的規范高寬尺寸是200cm×80cm;衛生間的門高寬是200cm×70cm。尺寸如有出入要及時糾正。

        2. Use a tape measure to measure the height and width of the hole. The width and height of the door is 200cm * 80cm, and the width of the bathroom door is 200cm * 70cm. If the size is in or out, it should be corrected in time.

        3、測量地位線,確定門框的地位,用墨斗彈拉出垂直線,一側門洞兩條垂直線。

        3、measure the status line, determine the status of the doorframe, use the ink bomb to pull out the vertical line, one side door and two vertical lines.

        4、在垂直線上用沖擊鉆打眼,孔眼與孔眼之間的間隔約爲30cm,一側門兩排共10個孔眼。沖擊鉆的鉆頭應爲12mm,所鉆孔眼深度約爲6cm。

        4. Drill holes on the vertical line with a percussion drill. The interval between the hole and the hole is about 30cm, and there are 10 holes in the two row of the side door. The drill bit for the percussion drill should be 12mm, and the depth of the drilling hole is about 6cm.

        5、將小木楔用鐵錘逐一釘入孔眼,以便固定門框板。小木楔的體積大小爲5cm×1.5cm×1.5cm,以落葉松制造的爲好,由于落葉松的木質構造緊,不容易松動。

        5. Hammer the small wooden wedge into the eyelet one by one, so that the door frame can be fixed. The size of the small wedge is 5cm * 1.5cm * 1.5cm, which is made of larch. Because the wood structure of larch is tight, it is not easy to loose.

        電梯門套

        6、開料制造門框。左右做兩側門框龍骨的木工板尺寸爲200cm× 3cm×8cm,門框頂龍骨的木工板尺寸爲80cm×3cm×8cm。將高密度九厘板涂膠粘在龍骨上,再用汽槍釘固定。

        6. Open the door frame. The size of the woodworking board with two sides of the doorframe keel is about 200cm * 3cm * 8cm, and the size of the woodwork board of the door frame keel is 80cm * 3cm * 8cm. Glue the high density nine - board to the keel and fix it with a steam gun.

        7、將制造好的三條門框按門的外形銜接起來,并且用大釘子在接合處固定。

        7.connect the three door frames that are made up according to the shape of the door, and fix them with the big nails at the joint.

        8、用刨子將銜接好的門框外表修平整,修整邊角,棱角清楚。

        8. Use the plane to smooth the appearance of the good doorframe, trim the edges and corners, and make the edges clear.

        9、將門框放到門洞上,按墻面的程度線爲準,門框下拿木頭或許磚頭墊起,調理門框的高度。上面預留5cm埋在地板的龍骨中。

        9. Put the doorframe on the doorway, according to the degree line of the wall, take wood or brick under the doorframe, and adjust the height of the doorframe. The 5cm is buried in the floor of the keel

        10、在門框的下面釘一個釘子,把線垂掛上,經過線垂來調整門框的垂直,一邊權衡一邊用麻花釘將門框固定在門洞上。

        10. Nail a nail under the doorframe, hang the line vertically, adjust the vertical of the door frame through the line droop, and balance the door frame on the door with the twist nail on the other side.

        11、制造門臉的線條。門臉可以是現成買的,也可以是施工人員依照圖紙做出來的。制造完成后,就把門臉固定到門框上六,這樣門套就根本完成了。

        11, make the line of the face. The door face can be bought on the spot, or it can be made by the construction personnel according to the drawings. After the manufacture is completed, the door face is fixed to six of the doorframe, so that the doorway is completely completed.

        12、把門放到門套上比劃好,確定合頁在門套上的詳細地位,再按合頁的厚度切出口徑。也切出鎖套的口徑。將門裝置到門套上,合頁用鑼絲刀將鑼絲釘擰緊。留意門與石塑電梯門套的間隙不得大于1.5mm,以順暢開關門爲準。

        12, put the door on the door sleeve to make a good decision, determine the detailed position of the hinge on the door cover, and then cut the caliber according to the thickness of the hinge. The bore of the lock is also cut out. The door is mounted on the door sleeve, and the hinge is tightened with a wire knife. Note that the clearance between door and stone elevator door can not be greater than 1.5mm, with a smooth opening and closing door as the criterion.

        毛片精品一区二区二区三区
        1. <table id="s6qli"></table>

            <td id="s6qli"></td>